The second stroke infusion fraud. Do you think that I need ink? Wrong, not the end, never compromise on the printer. Remove the ink cartridge and seal the ink outlet. Using a medical syringe, take 3 to 5 ml of distilled water. Inject (not too much) from the ink filling hole of the ink cartridge, and then vigorously shake the ink cartridge so that the water sinks to the ink outlet. Repeat this water injection process again so that there is 10 ml of ink in the cartridge. Urgent printing should be fine. You can also shake the ink cartridge several times. Let water repeatedly in the cartridge. Because each repetition, distilled water can dissolve more of the original ink. If the print quality is not high enough, you can hardly tell whether it is distilled water or a new one. With this method you can play nearly 100 pages. In fact, it is to make full use of the large sponge in the ink cartridge. It should be noted that distilled water must be used. There are too many ordinary water impurities. Remember to not be greedy. If too much distilled water is injected, the effect is not good. In addition, depending on your original ink quality, the printing effect will be close to the original ink. Particular attention should be paid to distinguishing what is the ink outlet and what is the ink inlet. Because there is a metal filter near the ink outlet. If you infuse ink from it, it will damage it, affecting the filter function causing plugging. Of course, this is just an emergency trick.
This is basically the case. As for alternative inks and inks, the ink will play better in terms of print quality. This is more. It is useful for Shanghai Hero Hero Premium Carbon Ink (very easy to plug), Zhejiang West Lake brand pure blue ink (unstable, faded) and Orb ink (light color), after several attempts to plug, especially recommended to poor buddies Needle pen ink (artificial use), because the fine arts and crafts workers use a fine needle pen, only 0.3mm, very few impurities, the color is very black after printing, the effect is very good. However, it is still the old saying that using alternative inks is not as good as the original ones. There will always be more chances of plugging. Please think twice.
8 big recommendations In addition, whether it is using compatible ink or alternative, there are several suggestions must be remembered:
1. Make sure the filled cartridge is intact;
2. To use high-quality original ink as much as possible to fill;
3. Before the ink is refilled, the original ink cartridge should be thoroughly cleaned. Otherwise, two different inks will mix and cause a chemical reaction, causing plugging and other failures. Do not use the printer's own procedure for cleaning the ink cartridges. This operation is not only time-consuming, but it is also not clean enough. The correct method of operation is: Before adding ink, use a syringe to inject pure water into the cartridge. Try not to let the water overflow. Then grasp the entire cartridge with your hand and turn the ink hole upwards and gently shake it a few times. The remaining ink is fully dissolved in the added clear water. Excessive force may cause the liquid inside to overflow when it is shaken. In this case, wipe it with a paper towel or cloth in time to prevent it from penetrating into the circuit board and cause a hardware failure. Then use a syringe to clean the mixed liquid in the cartridge. , so repeated operation several times, until you see the liquid color is very light to use the printer comes with the program to clean the ink cartridges;
4. When filling ink cartridges with ink, it must be appropriate;
5. Try to choose ink ink to fill;
6. After filling the cartridges with ink, it is best to let the cartridge stand still for a few minutes so that the ink slowly penetrates into all corners of the sponge pad to ensure the final print quality;
7. To avoid exposing the ink cartridge to dry air for a long period of time, despite the method of cleaning it, ink should be filled immediately after the cartridge is about to be inked, and the ink should be printed immediately after the ink is filled. If the printer is not in use for a while, it can also be placed in a special nozzle storage box, in which a special rubber pad can block the air and keep the nozzle wet;
8. If the ink cartridge and the print head are integrated together, when the ink is to be applied to the ink cartridge, care must be taken to protect the nozzle on the ink cartridge from harm. Otherwise, once the nozzle is blocked or damaged, the ink cartridge cannot be reused. In addition, due to the frequent use of the ink cartridge, the print head may be blocked by the splattered paper fibers, resulting in poor output of the print head. Therefore, it is very necessary to periodically clean the print head. When cleaning the nozzles, wipe the edges of the nozzles gently with a wet wipe and a non-perforated paper towel instead of hitting the nozzle. Then, use the cleaning button on the control panel of the inkjet printer to perform a cleaning action on the nozzles until the printout is finished. Clear so far.
This is basically the case. As for alternative inks and inks, the ink will play better in terms of print quality. This is more. It is useful for Shanghai Hero Hero Premium Carbon Ink (very easy to plug), Zhejiang West Lake brand pure blue ink (unstable, faded) and Orb ink (light color), after several attempts to plug, especially recommended to poor buddies Needle pen ink (artificial use), because the fine arts and crafts workers use a fine needle pen, only 0.3mm, very few impurities, the color is very black after printing, the effect is very good. However, it is still the old saying that using alternative inks is not as good as the original ones. There will always be more chances of plugging. Please think twice.
8 big recommendations In addition, whether it is using compatible ink or alternative, there are several suggestions must be remembered:
1. Make sure the filled cartridge is intact;
2. To use high-quality original ink as much as possible to fill;
3. Before the ink is refilled, the original ink cartridge should be thoroughly cleaned. Otherwise, two different inks will mix and cause a chemical reaction, causing plugging and other failures. Do not use the printer's own procedure for cleaning the ink cartridges. This operation is not only time-consuming, but it is also not clean enough. The correct method of operation is: Before adding ink, use a syringe to inject pure water into the cartridge. Try not to let the water overflow. Then grasp the entire cartridge with your hand and turn the ink hole upwards and gently shake it a few times. The remaining ink is fully dissolved in the added clear water. Excessive force may cause the liquid inside to overflow when it is shaken. In this case, wipe it with a paper towel or cloth in time to prevent it from penetrating into the circuit board and cause a hardware failure. Then use a syringe to clean the mixed liquid in the cartridge. , so repeated operation several times, until you see the liquid color is very light to use the printer comes with the program to clean the ink cartridges;
4. When filling ink cartridges with ink, it must be appropriate;
5. Try to choose ink ink to fill;
6. After filling the cartridges with ink, it is best to let the cartridge stand still for a few minutes so that the ink slowly penetrates into all corners of the sponge pad to ensure the final print quality;
7. To avoid exposing the ink cartridge to dry air for a long period of time, despite the method of cleaning it, ink should be filled immediately after the cartridge is about to be inked, and the ink should be printed immediately after the ink is filled. If the printer is not in use for a while, it can also be placed in a special nozzle storage box, in which a special rubber pad can block the air and keep the nozzle wet;
8. If the ink cartridge and the print head are integrated together, when the ink is to be applied to the ink cartridge, care must be taken to protect the nozzle on the ink cartridge from harm. Otherwise, once the nozzle is blocked or damaged, the ink cartridge cannot be reused. In addition, due to the frequent use of the ink cartridge, the print head may be blocked by the splattered paper fibers, resulting in poor output of the print head. Therefore, it is very necessary to periodically clean the print head. When cleaning the nozzles, wipe the edges of the nozzles gently with a wet wipe and a non-perforated paper towel instead of hitting the nozzle. Then, use the cleaning button on the control panel of the inkjet printer to perform a cleaning action on the nozzles until the printout is finished. Clear so far.
Frozen Meat Breaker And Grinder
Frozen meat breaker/frozen meat breaker/meat grinder/meat mincer is the first step of high quality products production. They are used for pre-breaking frozen meat blocks stacked on pallets. It includes bone saw series, frozen meat cutting machine, frozen meat flaker,grinder series, etc. Customers will use different machines depending on the processing needs and to form an automatic production line. No need of defrosting of the meat, Helper`s breaker series has been designed to cut off a whole block of meat in meat pieces with a blades system, avoiding second time pollution and keeping meat texture.
Large frozen meat breaker series: Bone saw, Frozen meat cutting machine, frozen meat flaker.
Frozen meat grinder series: JR-120, JR-140, JR-300, chopping and grinding combination system.
Rib Chopping Machine,Frozen Meat Flaker,Frozen Meat Cutter,Meat Mincer,Meat Grinder,Frozen Meat Breaker
Helper Machinery Group Co., Ltd. , https://www.helperfoodtek.com