Human apolipoprotein C3 (APO-C3) enzyme-linked immunoassay (ELISA)
Kit instruction manual
This reagent is for research purpose only: this kit is used to determine the content of apolipoprotein C3 (APO-C3) in human serum, plasma and related liquid samples.
Experimental principle:
This kit uses the double antibody sandwich method to determine the level of human apolipoprotein C3 (APO-C3) in the specimen. Microporous plates were coated with purified human apolipoprotein C3 (APO-C3) antibody to prepare solid-phase antibodies. Apolipoprotein C3 (APO-C3) was added to the microwells coated with mAb in turn, and then labeled with HRP The apolipoprotein C3 (APO-C3) antibody binds to form an antibody-antigen-enzyme-labeled antibody complex. After thorough washing, the substrate TMB is added for color development. TMB is converted into blue under the catalysis of HRP enzyme, and into the final yellow under the action of acid. The color depth is positively correlated with apolipoprotein C3 (APO-C3) in the sample. The absorbance (OD value) was measured with a microplate reader at a wavelength of 450 nm, and the concentration of human apolipoprotein C3 (APO-C3) in the sample was calculated by a standard curve.
Kit composition:
Kit composition
48 hole configuration
96-well configuration
save
Instructions
1 serving
1 serving
Sealing film
2 pieces (48)
2 pieces (96)
sealed bag
1
1
Enzyme coated plate
1 × 48
1 × 96
Store at 2-8 ℃
Standard product: 135ng / ml
0.5ml × 1 bottle
0.5ml × 1 bottle
Store at 2-8 ℃
Standard dilution
1.5ml × 1 bottle
1.5ml × 1 bottle
Store at 2-8 ℃
Enzyme reagent
3 ml × 1 bottle
6 ml × 1 bottle
Store at 2-8 ℃
Sample diluent
3 ml × 1 bottle
6 ml × 1 bottle
Store at 2-8 ℃
Developer A liquid
3 ml × 1 bottle
6 ml × 1 bottle
Store at 2-8 ℃
Developer B liquid
3 ml × 1 bottle
6 ml × 1 bottle
Store at 2-8 ℃
Stop solution
3ml × 1 bottle
6ml × 1 bottle
Store at 2-8 ℃
Concentrated washing liquid
(20ml × 20 times) × 1 bottle
(20ml × 30 times) × 1 bottle
Store at 2-8 ℃
Sample processing and requirements:
1. Serum: The blood will naturally coagulate at room temperature for 10-20 minutes and centrifuge for about 20 minutes (2000-3000 rpm). Collect the supernatant carefully and centrifuge again if a precipitate appears during storage.
2. Plasma: EDTA, sodium citrate or heparin should be selected as the anticoagulant according to the requirements of the specimen, mixed for 10-20 minutes, and centrifuged for about 20 minutes (2000-3000 rpm). Collect the supernatant carefully. If a precipitate forms during storage, it should be centrifuged again.
3. Urine: collected in a sterile tube and centrifuged for about 20 minutes (2000-3000 rpm). Collect the supernatant carefully. If a precipitate forms during storage, centrifuge again. Pleural and ascites, cerebrospinal fluid reference implementation.
4. Cell culture supernatant: When detecting secreted components, collect with a sterile tube. Centrifuge for about 20 minutes (2000-3000 rpm). Collect the supernatant carefully. When detecting the components inside the cells, dilute the cell suspension with PBS (PH7.2-7.4), and the cell concentration will reach about 1 million / ml. Through repeated freezing and thawing, the cells are destroyed and the intracellular components are released. Centrifuge for about 20 minutes (2000-3000 rpm). Collect the supernatant carefully. If a precipitate forms during storage, it should be centrifuged again.
5. Organize the specimen: after cutting the specimen, weigh it. Add a certain amount of PBS, PH7.4. Quickly freeze and save with liquid nitrogen for later use. After the specimen melts, it still maintains a temperature of 2-8 ° C. Add a certain amount of PBS (PH7.4) and homogenize the specimen with a manual or homogenizer. Centrifuge for about 20 minutes (2000-3000 rpm). Collect the supernatant carefully. After aliquoting, a portion is to be tested, and the rest is frozen for future use.
Steps
1. Dilution and loading of standard products: set 10 standard wells on the enzyme-coated plate, add 100 μl of standard products in the first and second wells, and then add standard products in the first and second wells 50μl of diluent, mix well; then take 100μl from the first well and the second well and add them to the third and fourth wells respectively, and then add 50μl of standard diluent to the third and fourth wells respectively, mix well; Then take 50μl each in the third and fourth wells and discard it, then add 50μl each to the fifth and sixth wells, and then add 50ul of the standard dilution solution to the fifth and sixth wells respectively, and mix well; After mixing, take 50μl from the fifth and sixth wells and add them to the seventh and eighth wells respectively. Then add 50μl of the standard dilution solution to the seventh and eighth wells respectively. Take 50μl from the eight wells and add them to the ninth and tenth wells. Then add 50μl of the standard dilution solution to the ninth and tenth wells. After mixing, take 50μl from the ninth and tenth wells and discard. (After dilution, the volume of each well is 50μl, and the concentrations are 90ng / ml, 60ng / ml, 30ng / ml, 15 ng / ml, 7.5 ng / ml).
2. Add samples: set up blank wells (the blank control wells do not add samples and enzyme reagents, the rest of the steps are the same) and the sample wells to be tested. Add 40μl of sample diluent to the test sample well of the enzyme-coated plate, and then add 10μl of the test sample (the final dilution of the sample is 5 times). Add the sample and add the sample to the bottom of the well of the microplate, try not to touch the wall of the well, shake gently to mix.
3. Incubation: Seal the plate with a sealing plate and incubate at 37 ° C for 30 minutes.
4. Mixing solution: Dilute 30 times (20 times of 48T) concentrated washing liquid with distilled water 30 times (20 times of 48T) and then use.
5. Washing: Carefully peel off the sealing film, discard the liquid, spin dry, fill each well with the washing liquid, let it stand for 30 seconds and then discard, repeat this 5 times, pat dry.
6. Add enzyme: add 50μl of enzyme label reagent to each well, except blank well.
7. Incubation: The operation is the same as 3.
8. Washing: The operation is the same as 5.
9. Color development: add 50μl of developer A to each well, then add 50μl of developer B, mix gently, and develop at 37 ° C in the dark for 15 minutes.
10. Termination: Add 50μl of stop solution to each well to stop the reaction (at this time the blue will turn to yellow).
11. Determination: Measure the absorbance (OD value) of each well in sequence with the blank air conditioner at zero and 450 nm wavelength. The measurement should be carried out within 15 minutes after adding the stop solution.
Precautions:
1. The kit should be equilibrated at room temperature for 15-30 minutes before being taken out of the refrigerated environment. If the enzyme label coated plate is unopened, the strip should be stored in a sealed bag.
2. Crystals may be precipitated in the concentrated washing liquid, which can be heated and dissolved in a water bath during dilution, and the results will not be affected during washing.
3. The sampler should be used at each step of sample addition, and the accuracy should be regularly checked to avoid test errors. It is best to control the sampling time within 5 minutes. If there are many specimens, it is recommended to use a volley gun to add samples.
4. Please make a standard curve at the same time of each measurement, it is best to make a double hole. If the content of the test substance in the specimen is too high (the OD value of the sample is greater than the OD value of the first well of the standard well), please first dilute it with a certain multiple (n times) of the sample diluent and then determine it. When calculating, please multiply the total dilution Multiple (× n × 5).
5. The sealing film is limited to one-time use to avoid cross-contamination.
6. Please keep the substrate away from light.
7. Strictly follow the instructions, and the test results must be determined by the microplate reader.
8. All samples, washing liquids and various wastes should be treated as infectious agents.
9. The components of different batches of this reagent shall not be mixed.
10. If there is any difference with the English manual, the English manual shall prevail.
Calculation:
Taking the concentration of the standard as the abscissa and the OD value as the ordinate,
Draw a standard curve on coordinate paper, according to the OD of the sample
The value is determined by the standard curve; then multiplied by the dilution
Multiple; or calculate the standard using the concentration and OD value of the standard
The linear regression equation of the quasi-curve, the OD value of the sample
Substitute into the equation, calculate the sample concentration, and multiply by the dilution
The multiple is the actual concentration of the sample.
(This picture is for reference only)
Kit performance:
1. The correlation coefficient R between the linear regression of the sample and the expected concentration is above 0.95.
2. The batch and approval shall be less than 9% and 11% respectively
examination range:
3 ng / ml – 120ng / ml
Storage conditions and validity period:
1. Store the kit: 2-8 ℃.
2. Validity: 6 months
Lip brush is an essential tool for beauty. Whether it is refreshing light makeup; or bright and heavy makeup, Makeup Brushes are also indispensable. Appropriate application can make makeup look more durable and the effect is more perfect and natural. There are many types of makeup brushes. Lip Brushes are Makeup Tools for applying lipstick. It can make the contour of the lip line clear and the color of the lipstick even. Choose a lip brush with a stiffer and finer hair to help draw the lip line and apply color. Even from an economic point of view, it is necessary to prepare more lip brushes. The lip brush can easily use the remaining lipstick in the lipstick tube, and it is not wasted at all; if there is no Lip Liner , it can also be used to draw lip lines; if there are several lipsticks, you can use the lip brush to bring out new colors Make your lip color unique. More importantly, using Lipstick Brush to apply lipstick is more dexterous, and the color will be more uniform and detailed.
Benefits
Advantages and disadvantages of a lip brush: The advantage of a lip brush is that it can accurately outline the outer contour of the lips, and can handle details that are not well handled such as the corners of the mouth. If you use a lip brush to dipped in lipstick, you usually use a thin and light color to paint the same color as the paste through multiple layers. You can see the different effects of different thicknesses. Because of the characteristics of lip brushes, makeups that generally require lip effects, such as lip bite makeup, need to be completed with a lip brush.
The disadvantage is that if you want to achieve the true color of the lipstick in one go, you have to brush it several times. In this case, you can directly apply the lipstick after the outline details of the lip brush.
Product Usage
1. Lip brush can help you repair lip defects and fill lip lines to the greatest extent.
2. Make the lip color fuller, not floating, and make your lip makeup more convincing.
3. Restore the true color of lipstick to the greatest extent.
Product Categories
According to the function of the lip brush:
1. Oblique lip brush: more suitable for contouring the lines of lip peaks.
2. Thin round lip brush: suitable for contouring inner lip corner lines.
According to the material of the lip brush:
1. Mink hair lip brush: It has excellent polymerization, elasticity and durability. Mao Feng is delicate and flexible. It is used for applying lipstick. It has high accuracy and flat lines. It can depict delicate lips. It is generally used for teaching and professional makeup.
2. Nylon lip brush: Made of high-grade synthetic fiber, with small bristles gap, high aggregation force, flat and long bristles, easy to master the strength, high accuracy when applying lipstick, flat lines, and can depict more delicate lips. The disadvantage is that after using for a long time, the hair tip will appear curled. Can be used for teaching and professional makeup.
3, horse hair lip brush: made of natural horse hair, soft and delicate, good polymerization, but poor elasticity.
4, silicone lip brush: made of food-grade silicone material, environmentally friendly, non-toxic, tasteless, reusable, easy to clean, compared to hair brushes, silicone lip brushes will be slightly harder, but the lip line effect is good , Is a new material lip brush emerging on the market. They have different shapes, such as heart shape, round head, pointed tip, etc., which can be selected according to personal preference.
Lip Brushes
Lip Brushes,Lipstick Brush,Lip Makeup Brush,Retractable Lip Brush
HENAN BON INDUSTRIAL(COSMETIC) CO.,LTD , https://www.boncosmetic.com